In recent years, with the progress of society, electric roller shutter is now widely used, widely used in factories, communities and other places. It can be seen everywhere in the current life. How to set the circuit of roller shutter, and the door industry to understand it.

　　一、如何安排卷簾門的接線

　　1、 How to arrange the connection of rolling shutter door

　　1、如果您選擇只需要遙控，那么只需讓電工在窗簾箱或窗簾安裝面附近留下一個電位差并安裝插座，但要注意這個電位差要求的箱子是“86型”的。

　　1. If you choose to only use remote control, you only need to let the electrician leave a potential difference near the curtain box or curtain installation surface and install the socket, but note that the box required by the potential difference is "86 type".

　　2、如果你選擇既有遙控器又有手動控制面板，那就讓電工在墻上開一個電位器，注意使用底箱的位置并引線一根三芯導線(單軌一根，雙軌需要兩根)。每個電動卷簾門軌道電機必須連接到一根三芯導線上，二軌電機零線不能共用。

　　2. If you choose to have both remote control and manual control panel, ask the electrician to open a potentiometer on the wall, pay attention to the position of the bottom box and lead a three-core wire (one for single track and two for double track). Each track motor of electric rolling shutter door must be connected to a three core conductor, and the zero line of two track motor cannot be shared.

　　如何給電動卷簾門裝電線?

　　How to wire the electric roller shutter?

　　二、如何連接卷簾門電機控制線

　　2、 How to connect the roller shutter motor control line

　　1. 在需要安裝的門框開口處畫一條線。指出尺寸，然后讓工作人員設計一個合適的電動門。這里重要的一點是，框架內的高度比門的高度稍高一些。

　　1. Draw a line at the opening of the door frame to be installed. Point out the size, then let the staff design a suitable electric door. The important point here is that the height of the frame is slightly higher than the height of the door.

　　2、先將百葉門框固定，在這里將門框下部的固定板取下;孔兩側地面預留溝槽，經校準合格后，將木楔、門框鐵腳及預埋鐵板固定焊接牢固。水泥砂漿或強度不小于10MPa的細石混凝土嵌塞能牢固。

　　2. Fix the shutter door frame first, and take down the fixing plate at the lower part of the door frame here; reserve grooves on the ground at both sides of the hole, and fix and weld the wooden wedge, the iron foot of the door frame and the embedded iron plate firmly after the calibration is qualified. Cement mortar or fine aggregate concrete with strength not less than 10MPa can be firmly embedded.

　　3.安裝電動門的主扇。一定要確保卷簾門與墻體形成一個整體，封閉性要做好，然后油漆孔和墻面。抹灰完成后，門縫應平整平整，打開卷簾門應自由移動，不得有過緊、過松和回彈現象。

　　3. Install the main fan of the electric door. Make sure that the rolling shutter door and the wall form a whole, and the sealing shall be done well, and then paint holes and walls. After plastering, the door joint shall be flat and flat, and the rolling shutter door shall move freely without over tightening, over loosening and rebound.

　　以上是濟南卷簾門公司關于電動卷簾門行業如何設置配線的一些介紹，但需要提醒的是，以上預留的位置是為了保證隨時可以通電，如果您對我們的產品感興趣，您可以打電話聯系我們。

　　The above is the introduction of Jinan roller shutter company on how to set up wiring in the electric roller shutter industry, but it should be reminded that the above reserved position is to ensure that the power can be connected at any time. If you are interested in our products, you can call us.